Bespoke Cut - IP65 Up to 20M Super Length Continuous Run LED Nano COB Strip IP65 8W 2700K Very Warm White

For a customised LED strip quotation, please email your requirements to sales@uno-lighting.com

8W/m Dotless LED Strip – 2700K – Bespoke Cut – 24V – 10mm – Indoor IP65 - Uno Lighting

A professional-grade 24V ultra-long-run dotless LED strip with a fully bespoke cutting and soldering service, allowing you to order the strip prepared to the specific length required for your project.

Featuring built-in IC technology and 384 LEDs per metre, this 8W/m strip provides smooth, seamless and dot-free illumination, delivering up to 720lm per metre with CRI 90. The 2700K Very Warm White output creates a soft and welcoming atmosphere, ideal for residential, hospitality and decorative indoor lighting applications.

Bespoke lengths can be prepared up to 20 metres, with built-in IC technology allowing a continuous run of up to 20m to be powered from one end while helping to minimise voltage drop and maintain consistent brightness.

Product Specifications

Colour Temperature Guide

Fully Bespoke Cutting Service

We prepare the LED strip to your required length before dispatch, providing a convenient, installation-ready solution for bespoke lighting projects.

As standard, we will:

• Cut the LED strip to your requested length

• Solder a 150mm power cable to the end

• Protect the soldered connection and joint with heat shrink

• Test the completed LED strip before dispatch

If you require a longer power tail, bridge leads, corner leads, multiple sections or another specific configuration, please email your requirements to sales@uno-lighting.com for a customised quotation.

Please note that the strip has a 56mm cutpoint, so requested bespoke lengths will need to correspond with the nearest available cutting position.

Bespoke Preparation Time

Our bespoke cutting service for this Indoor IP65 spray-coated LED strip normally takes approximately 2–3 working days to prepare before dispatch.

Because the Indoor IP65 protection uses a spray coating rather than a silicone sleeve, we can prepare and protect the soldered connection with heat shrink without the additional sealing and curing processes required by some other IP-rated LED strips.

For larger quantities or more complex bespoke configurations, preparation may take longer. We will advise you if additional preparation time is required.

Ultra Long Run Performance

Built-in IC technology is specifically designed to provide consistent performance across longer LED strip installations.

This bespoke listing supports individual continuous lengths of up to 20 metres powered from one end, helping to minimise voltage drop and maintain consistent brightness across the run.

Although the underlying LED strip technology can support alternative power configurations, the maximum individual bespoke length available through this listing is 20 metres.

Driver Requirements

This LED strip operates at 24V DC and must not be connected directly to 230V mains electricity.

A suitable 24V constant-voltage LED driver is required and is sold separately. The driver should be correctly sized according to the total wattage and length of LED strip being ordered.

For example, a full 20m length has a total LED strip load of 160W (20m × 8W/m), so the driver and installation should be appropriately sized for the required length.

The strip supports PWM dimming when used with a compatible 24V dimmable driver or controller.

Installation & Indoor IP65 Protection

We recommend installing the LED strip within a suitable aluminium LED profile to provide heat dissipation, additional protection and a professional finished appearance.

The Indoor IP65 protection is provided by a spray coating rather than a silicone sleeve. As part of the bespoke service, the soldered joint is covered with heat shrink to provide protection to the connection.

This product is intended for indoor applications only and is not recommended for permanent outdoor installation.

Avoid excessive bending, twisting or pressure on the LED strip or bespoke soldered connections during installation.

Warranty

This bespoke LED strip is supplied with a 2-year warranty.

The warranty is extended to 3 years when the LED strip is purchased and installed with a suitable Uno Lighting aluminium profile, helping provide appropriate heat dissipation and protection for long-term performance.

Important Bespoke Order Information

• This listing is for a bespoke cut and prepared LED strip; the LED driver, controller and aluminium profile are sold separately unless otherwise stated.

• The standard power tail supplied with each prepared length is 150mm.

• Longer tails, bridge leads, corner leads and other configurations can be requested by contacting us before ordering.

• Bespoke lengths are prepared according to the strip's 56mm cutting interval.

• Maximum individual bespoke length through this listing is 20m.

• Bespoke preparation normally takes approximately 2–3 working days before dispatch.

• All completed bespoke LED strips are tested before dispatch.

• Due to the customised nature of the product, bespoke cut LED strips are non-cancellable and non-returnable once the order has been placed.

• Promotional discounts and offers do not apply to the bespoke cutting service unless specifically stated.

• Please ensure the length, voltage, wattage, dimensions, colour temperature and IP rating meet your requirements before ordering.

• Installation must be carried out by a suitably qualified person.

Electrical Installation Disclaimer

Uno Lighting cannot provide site-specific electrical installation instructions. All mains electrical connections and installation work must be carried out in accordance with applicable electrical regulations by a suitably qualified professional.